Internal elements of the car body Chevrolet Niva 1

Removal and installation the instrument panel
Disconnect the ground cable from the battery. Remove the horn switch, unscrew the steering wheel mounting nut and remove the steering wheel. Unscrew the screws...

Removal the interior equipment of the car
Remove the self-tapping screws 1 (figure 8-52) and remove sun visors 4 and 17. Unscrew two screws 3 and remove interior rear-view mirror 2. Figure 8-52....

Removal and installation front seats
The arrangement of the front seats is shown in Figure 8-53. Figure 8-53. Installing the front seats: 1 - nut; 2 - seat movement mechanism lever; 3 - bolt; 4 -...

Removal and installation the rear seat
The rear seat is designed as two seats, each of which can be easily folded, thereby increasing the luggage compartment space. To remove the right side of the...

Windscreen washers
The windshield washer circuit is shown in Figure 8-56. It consists of a washer reservoir 3, which has two niches for mounting the windshield and headlight...

Removal and installation the windshield
Remove the windshield in the following order: lift the hood, disconnect the negative terminal of the battery; unscrew screws 1 (figure 8-59) and remove the...

Windshield installation
Check the size of the gaps around the perimeter of the glass adjoining the windshield frame. The size of the gaps should not exceed 2 mm. Degrease the edges of...

Side glass replacement
Press the plastic holders of the rear pillar trim and remove the trim. Remove trim 1 (figure 8-61) side window glass, cut the adhesive seam 3 and remove glass...

Replacement of rear door glass
Remove the spare wheel cover, unscrew the three nuts and remove the wheel. Loosen the nut and remove the rear door wiper arm. Overcoming the resistance of the...

Removal car body upholstery
Removing the body floor trim is shown in Figure 8-78. Figure 8-78. Body floor trim: 1 - screw; 2 - Transfer case lever cover; 3 - gear lever cover; 4 - floor...

Removal the shield and front wing cover
Unscrew bolts 5 (figure 8-80) and remove the front wing shield with seals 4 as an assembly. Figure 8-80. Removing the front fender shield and cover: 1 - screw;...

Removal the shield and front wing cover for assembly 55
Removal the apron Remove two screws 1 (figure 8-81) fastenings of mudguard apron 2. Figure 8-81. Fastening the apron: 1 - screw; 2 - dirt-protecting apron....

Removal and installation the gearshift lever and transfer case for the 55 configuration
Removal Disengage and detach covers 1 and 3 (Fig. 8-85) from the floor tunnel lining 5. Unscrew handles 2 and 4 of the gearbox and transfer case. Remove the...

Removal and installation the gearbox and transfer case handle inserts for the 55 configuration
Figure 8-86. Gearbox and transfer case handle inserts: 1 - gearshift handle insert (chrome inserts for GLS and GLC trim) 2 - Transfer case handle insert; 3 -...

Removal and installation the floor tunnel lining for assembly 55
Removal Disconnect the negative terminal of the battery cable. Remove the gearbox and transfer case lever handles according to the chapter " Gearbox and...

Removal and installation roof trim for trim level 55
Removal the roof lining Place the vehicle on a work post, lift the hood, and disconnect the ground wire terminal from the battery. Remove two plastic plugs 1...

Removal and installation of right/left roof rails for configuration 55
Removal Remove the trims 1 (figure 8-111) railing 2. Figure 8-111. Railing mount: 1 - roof rail trim; 2 - roof rail; 3 - nut; 4 - seal. Unscrew five nuts 3....

Removal and installation roof brackets for assembly 55
Removal Remove the roof rails by chapter " Right/left roof rail - removal and installation ". Remove the headliner according to the chapter " Roof lining -...

Removal car body trims and moldings
Use a screwdriver to pry off moldings 2, 4 and 5 (figure 8-113) front wing, front and rear doors, remove them. Use a knife to cut off the glue seam and remove...

Removal and installation floor sill fairings for 55 configuration
Removal Remove two screws 1 (figure 8-114) fastenings of apron 2, release fairing 3 from connection with apron. Figure 8-114. Side mount of the threshold...

Removal and installation of front and rear wheel arch trims for assembly 55
Removal Remove five screws 1 (figure 8-118) fastenings of cladding 2. Figure 8-118. Installing the cladding: 1 - screw; 2 - front wheel arch lining. Remove the...

Removal and installation front seat belts
Remove six screws 1 (figure 8-122) fastenings of the front threshold trim, remove trim 2. Figure 8-122. Front threshold trim: 1 - screw; 2 - front threshold...

Removal the rear seat belts
Figure 8-129. Rear seat belts: 1 - right seat belt; 2 - left seat belt; 3, 6 - left/right side seat belt locks; 4 - middle seat belt lock; 5 - middle seat...

Removal and installation the interior rearview mirror
Overcoming the resistance of the spring clip 1 (figure 8-134) pull mirror 2 down parallel to the plane of the glass until it comes out of the groove of the...

This section is available at russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share information: