1. Loosen the wheel nuts, raise the front of the vehicle and install vertical supports. Remove the wheels. Support both lower control arms with floor jacks.
2. Remove the protective panel located on the underside of the vehicle.
3. Unscrew the bolts securing the lower suspension arm bracket to the frame (see chapter 10).
4. Unscrew the mounting bolts and remove the front steering gear cross member.
5. Unscrew the mounting bolts and remove the rear cross member of the steering gear.
6. Installation is carried out in the reverse order of removal. Tighten the lower control arm bracket mounting bolts to the torque value given in chapter 10 specifications. Tighten the steering gear bridge bolts to the specified torque.
Information taken from the official website ChevyMan.ru
Steering gear jumper — removal and installation (Chevrolet Trailblazer 1)
The article was checked: Vladimir Romannikov
This article is available at russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Share information:
Previous articles
Trailblazer 1: Interior (internal elements)
Next articles
See similar articles on the topic of Chevrolet cars:
Adjusting the clearance of the gear engagement in the steering mechanism Chevrolet Aveo T250 (2006-2011)
Steering Gear Diagnostic Trouble Codes Chevrolet Captiva 1 (2006-2018)
Replacing the steering gear Chevrolet Cruze 1 (2008-2016)
Replacing the steering gear cover Chevrolet Lacetti 1 (2002-2009)
Removal the steering gear Chevrolet Lanos T150 (2002-2009)
Removal and installation the power steering gear Chevrolet Niva 1 (2002-2016)
Steering gear — removal and installation Chevrolet Tahoe 1 (1992-2000)
Adjusting the clearance of the gear engagement in the steering mechanism Chevrolet Aveo T250 (2006-2011)
Steering Gear Diagnostic Trouble Codes Chevrolet Captiva 1 (2006-2018)
Replacing the steering gear Chevrolet Cruze 1 (2008-2016)
Replacing the steering gear cover Chevrolet Lacetti 1 (2002-2009)
Removal the steering gear Chevrolet Lanos T150 (2002-2009)
Removal and installation the power steering gear Chevrolet Niva 1 (2002-2016)
Steering gear — removal and installation Chevrolet Tahoe 1 (1992-2000)
Link in different formats to this page
Visitor comments
No comments yet
- General information
- Introduction to manual
- User manual
- Maintenance
- Troubleshooting
- Power unit
- Engine repair
- Fuel and control system
- Cooling and lubrication system
- Ignition system
- Transmission
- Clutch
- Gearbox
- Drive shafts
- Chassis
- Car suspension
- Steering
- Brake system
- Body
- Exterior (external elements)
- Doors, locks and windows
- Electrical equipment
- Equipment and devices
- Windscreen wipers
- Power devices
- Electrical diagrams
- General information
- User manual
- Troubleshooting
- Maintenance
- Power unit
- Engine in a car
- Engine overhaul
- Cooling and heating
- Fuel and exhaust system
- Engine electrical equipment
- Engine control
- Transmission
- Automatic gearbox
- Transfer case
- Drive shafts and cardan
- Chassis
- Brake system
- Car suspension
- Steering
- Body
- Exterior (external elements)
- Interior (internal elements)
- Doors, locks and windows
- Electrical equipment
- Equipment and devices
- Electrical circuits
- General information
- Maintenance
- Power unit
- Engine 3.1L V6
- Engine 3.8L V6
- Engine overhaul
- Cooling system
- Power and exhaust system
- Fuel injection
- Engine electrical equipment
- Reduced exhaust gas toxicity
- Transmission
- Automatic gearbox
- Drive shafts
- Chassis
- Brake system
- Car suspension
- Steering
- Body
- Heating and air conditioning
- Repair of body elements
- Doors, covers and windows
- Interior (internal elements)
- Electrical equipment
- Equipment and devices
- Electrical circuits