Doors, locks and windows of the car Chevrolet Cruze 1

Removal and installation the front door trim
You will need: TORX T20 key, flat-blade screwdriver. 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the screw securing the...

Front door glass replacement
You will need: a 10 mm socket head and a Phillips-head screwdriver. 1. Remove the front door trim and moisture-proof film (ref. " Removal and installation the...

Replacing the front door window regulator
The front door window lifters are equipped with an electric drive. This subsection describes only the removal and installation of the electric window lifter...

Replacing the front door outer handle
You will need: TORX T20 and 10 keys, flat-head and Phillips-head screwdrivers. Remove the front door trim and moisture-proof film. 2. Use a screwdriver to...

Replacing the front door lock
You will need: TORX keys T30 and T40, a Phillips-head screwdriver. 1. Remove the front door trim and moisture-proof film (see " Removal and installation the...

Replacing the inner handle of the front door lock actuator
You will need: TORX T20 key, flat-blade screwdriver. 1. Remove the front door trim (see " Removal and installation the front door trim "). 2. Use a screwdriver...

Removal and installation the front door
You will need a 10 mm wrench. 1. Remove the bolt and disconnect the door opening limiter from the front pillar (see " Replacing the front door opening limiter...

Replacing the front door opening limiter
You will need a 10 mm socket head. 1. Raise the glass and remove the front door trim (see " Removal and installation the front door trim "). 2. Remove the...

Removal and installation the rear door trim
You will need: TORX T20 key, flat-head and Phillips-head screwdrivers. 1. Pry it off with a screwdriver. 2. Remove the decorative cover of the inner handle of...

Rear door glass replacement
You will need: a 10 mm socket head and a Phillips-head screwdriver. 1. Remove the rear door trim and moisture-proof film (see " Removal and installation the...

Replacing the rear door window regulator
You will need a 10 mm wrench. 1. Remove the rear door trim and moisture-proof film (see " Removal and installation the rear door trim "). 2. Remove the rear...

Replacing the outer rear door handle
You will need: TORX T20 and 10 keys, flat-head and Phillips-head screwdrivers. 1. Remove the rear door trim and moisture-proof film (see " Removal and...

Replacing the inner handle of the rear door lock actuator
You will need: TORX T20 key, flat-blade screwdriver. 1. Remove the rear door trim and moisture-proof film (see " Removal and installation the rear door trim...

Replacing the rear door lock
You will need: TORX keys T30 and T40, a Phillips-head screwdriver. 1. Remove the rear door trim and moisture-proof film (see " Removal and installation the...

Replacing the rear door opening limiter
You will need a 10 mm socket head. 1. Raise the glass and remove the rear door trim and moisture-proof film (see " Removal and installation the rear door trim...

Removal and installation the trunk lid trim
You will need a flat-blade screwdriver. 1. Use a screwdriver to pry up the trunk lid lock trim... 2. ...and remove the trim. 3. Using a screwdriver, pull out...

Removal and installation the decorative trim on the trunk lid
You will need a 10 mm socket head. 1. Remove the trunk lid trim (see " Removal and installation the trunk lid trim "). 2. Unscrew the four nuts securing the...

Replacement of the lock, latch and trunk lid release button
You will need: TORX T30 key, 10 mm socket head, flat-blade screwdriver. To remove the trunk lid lock, perform the following steps. 1. Remove the trunk lid trim...

Removal and installation the trunk lid
You will need: a 10 mm wrench, a flat-blade screwdriver. 1. Remove the left side trim of the luggage compartment (see " Removal and installation trunk trims...

Removal and installation the fuel tank filler pipe hatch cover
1. Open the filler pipe hatch cover and unscrew the fuel tank cap by turning it counterclockwise. 2. Overcoming the resistance of the four clamps, remove the...

Replacement of fixed body glazing
The windshield and rear window glass are glued into the body openings. They are replaced using the same techniques, so the work is shown using the windshield...

This section is available at russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share information: