Doors, locks and windows of the car Chevrolet Aveo 2 (T300)
Removal and installation the front door trim
You will need: a 7 mm socket head, a plastic mounting blade, and a flat-blade screwdriver. 1. Disconnect the wire from the negative terminal of the battery. 2....
You will need: a 7 mm socket head, a plastic mounting blade, and a flat-blade screwdriver. 1. Disconnect the wire from the negative terminal of the battery. 2....
Front door glass replacement
You will need a 10 mm socket head. 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the front door trim (see " Removal and...
You will need a 10 mm socket head. 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the front door trim (see " Removal and...
Removal and installation the front door window regulator
You will need: a 10 mm socket head, masking tape. The front door window lifters are equipped with electric drives. This subsection describes the removal and...
You will need: a 10 mm socket head, masking tape. The front door window lifters are equipped with electric drives. This subsection describes the removal and...
Replacing the inner handle of the front door lock actuator
The inner handle of the front door lock actuator is not removable. Therefore, if the inner handle breaks, replace the front door trim assembly (see " Removal...
The inner handle of the front door lock actuator is not removable. Therefore, if the inner handle breaks, replace the front door trim assembly (see " Removal...
Replacing the outside handle and front door lock switch
You will need: TORX T20 key, flat-blade screwdriver. 1. Pry up the plug at the end of the door and remove the plug. 2. Turn the screw of the locking bracket of...
You will need: TORX T20 key, flat-blade screwdriver. 1. Pry up the plug at the end of the door and remove the plug. 2. Turn the screw of the locking bracket of...
Replacing the front door lock
You will need: TORX T20, TORX T30 keys, a 10 mm socket head, flat-head and Phillips-head screwdrivers. 1. Disconnect the wire from the negative terminal of the...
You will need: TORX T20, TORX T30 keys, a 10 mm socket head, flat-head and Phillips-head screwdrivers. 1. Disconnect the wire from the negative terminal of the...
Replacing the front door opening limiter
You will need the "by 10"key (better socket head). 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the front door trim (see "...
You will need the "by 10"key (better socket head). 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the front door trim (see "...
Removal and installation the front door
You will need: a wrench and a 10 mm socket head. 1. Disconnect the wire from the negative terminal of the battery. 2. Open the front door. 3. Press the lock......
You will need: a wrench and a 10 mm socket head. 1. Disconnect the wire from the negative terminal of the battery. 2. Open the front door. 3. Press the lock......
Adjusting the front door lock latch
You will need a TORX T35 key. If the door lock closes with difficulty or does not close at all, adjust the position of the door lock latch. To do this, follow...
You will need a TORX T35 key. If the door lock closes with difficulty or does not close at all, adjust the position of the door lock latch. To do this, follow...
Removal and installation the rear door trim
You will need: a 7 mm socket head, a plastic mounting blade, and a flat-blade screwdriver. 1. Disconnect the wire from the negative terminal of the battery. 2....
You will need: a 7 mm socket head, a plastic mounting blade, and a flat-blade screwdriver. 1. Disconnect the wire from the negative terminal of the battery. 2....
Replacing the rear door glass
You will need: a 7 mm wrench, a 10 mm socket head, and a Phillips-head screwdriver. 1. Disconnect the wire from the negative terminal of the battery. 2. Remove...
You will need: a 7 mm wrench, a 10 mm socket head, and a Phillips-head screwdriver. 1. Disconnect the wire from the negative terminal of the battery. 2. Remove...
Replacing the fixed rear door glass
You will need: a 7 mm wrench, a 10 mm socket head, and a Phillips-head screwdriver. 1. Remove the rear door glass (see " Replacing the rear door glass "). 2....
You will need: a 7 mm wrench, a 10 mm socket head, and a Phillips-head screwdriver. 1. Remove the rear door glass (see " Replacing the rear door glass "). 2....
Removal and installation the rear door window regulator
You will need: a 7 mm wrench, a 10 mm socket head, and masking tape. The rear door window lifters are equipped with electric drives. This subsection describes...
You will need: a 7 mm wrench, a 10 mm socket head, and masking tape. The rear door window lifters are equipped with electric drives. This subsection describes...
Replacing the inner handle of the rear door lock actuator
The inner handle of the rear door lock actuator is not removable. Therefore, if the inner handle breaks, replace the rear door trim assembly (see " Removal and...
The inner handle of the rear door lock actuator is not removable. Therefore, if the inner handle breaks, replace the rear door trim assembly (see " Removal and...
Replacing the outer rear door lock handle
You will need: TORX T20 key, flat-blade screwdriver. 1. Pry up the plug at the end of the door and remove the plug. 2. Turn the outer handle base locking...
You will need: TORX T20 key, flat-blade screwdriver. 1. Pry up the plug at the end of the door and remove the plug. 2. Turn the outer handle base locking...
Replacing the rear door lock
You will need: 7 mm keys, TORX T20, TORX T30, 10 mm socket head, flat-head and Phillips-head screwdrivers. 1. Disconnect the wire from the negative terminal of...
You will need: 7 mm keys, TORX T20, TORX T30, 10 mm socket head, flat-head and Phillips-head screwdrivers. 1. Disconnect the wire from the negative terminal of...
Replacing the rear door opening limiter
You will need the "by 10"key (better socket head). 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the rear door trim (see "...
You will need the "by 10"key (better socket head). 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the rear door trim (see "...
Removal and installation the rear door
You will need: a wrench and a 10 mm socket head. 1. Disconnect the wire from the negative terminal of the battery. 2. Open the front door. 3. Press the lock......
You will need: a wrench and a 10 mm socket head. 1. Disconnect the wire from the negative terminal of the battery. 2. Open the front door. 3. Press the lock......
Adjusting the rear door lock latch
You will need a TORX T40 key. If the rear door lock is difficult to close or does not close at all, adjust the position of the door lock latch. The adjustment...
You will need a TORX T40 key. If the rear door lock is difficult to close or does not close at all, adjust the position of the door lock latch. The adjustment...
Removal and installation the trunk lid trim
You will need a plastic spudger or a flat-blade screwdriver. 1. Open the trunk lid. 2. Pull out the thirteen clips securing the trunk lid trim (figure 11.3)......
You will need a plastic spudger or a flat-blade screwdriver. 1. Open the trunk lid. 2. Pull out the thirteen clips securing the trunk lid trim (figure 11.3)......
Removal, installation and adjusting the trunk lid lock
You will need: TORX T30 key, 10 mm socket head. 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the trunk lid trim (see " Removal...
You will need: TORX T30 key, 10 mm socket head. 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the trunk lid trim (see " Removal...
Removal and installation the decorative trim on the trunk lid
You will need a 10 mm socket head. 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the trunk lid trim (see " Removal and...
You will need a 10 mm socket head. 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the trunk lid trim (see " Removal and...
Removal and installation the trunk lid
You will need: a 10 mm socket head, a plastic mounting blade or a flat-blade screwdriver, and a marker. 1. Disconnect the wire from the negative terminal of...
You will need: a 10 mm socket head, a plastic mounting blade or a flat-blade screwdriver, and a marker. 1. Disconnect the wire from the negative terminal of...
This section is available at russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
See similar sections on Chevrolet cars:
Manual: Keys, doors and windows Chevrolet Captiva 1 (2006-2018)
Body: Doors, covers and windows Chevrolet Cruze 1 (2008-2016)
Body (until 2007): Doors, locks and windows Chevrolet Tahoe 2 and 3 (2000-2014)
Body: Doors, locks and windows Chevrolet Trailblazer 1 (2001-2008, petrol)
Manual: Keys, doors and windows Chevrolet Captiva 1 (2006-2018)
Body: Doors, covers and windows Chevrolet Cruze 1 (2008-2016)
Body (until 2007): Doors, locks and windows Chevrolet Tahoe 2 and 3 (2000-2014)
Body: Doors, locks and windows Chevrolet Trailblazer 1 (2001-2008, petrol)
Share information:
- General information
- Vehicle device
- User manual
- Main malfunctions
- Maintenance
- Power unit
- Engine
- Lubrication system
- Cooling system
- Supply system
- Exhaust system
- Transmission
- Clutch
- Manual gearbox
- Automatic gearbox
- Front wheel drives
- Chassis
- Front suspension
- Rear suspension
- Steering
- Brake system
- Body
- Exterior
- Interior
- Doors and trunk
- Security systems
- Electrical equipment
- Engine electrics
- Equipment and devices
- Heating and air conditioning
- Electrical circuits
- Manual
- Driver's workplace
- Salon equipment
- Vehicle characteristics
- Maintenance
- Engine 1.5 SOHC
- Engine repair
- Fuel supply system
- Control system
- Cooling system
- Engine 1.6 DOHC
- Engine repair
- Control system
- Transmission
- Clutch
- Manual gearbox
- Automatic gearbox
- Wheel drive
- Chassis
- Wheel suspension
- Steering
- Brake system
- Body
- Exterior
- Interior
- General information
- User manual
- Power unit
- Engine repair 1.5L SOHC
- Fuel system
- Control system
- Cooling system
- Transmission
- Clutch
- Manual gearbox
- Automatic gearbox
- Drive shafts
- Chassis
- Front suspension
- Rear suspension
- Steering
- Brake system
- Body
- Exterior (external elements)
- Interior (internal elements)
- Electrical equipment
- Equipment and devices
- Electrical circuits