Exterior elements of the car body Chevrolet Aveo 2 (T300)

Features of the body design
The Chevrolet Aveo car body is all-metal, load-bearing structure, like a sedan or a five-door hatchback. The body frame includes the base, sidewalls, roof and...

Possible body defects, their causes and methods of elimination

Removal and installation the front bumper
You will need: TORX T20 key, 10 mm socket head, flat-blade screwdriver, plastic mounting blade. 1. Remove the front mudguards, see. " Removal and installation...

Removal and installation the rear bumper
You will need: TORX T20 key, flat-head and Phillips-head screwdrivers. 1. Remove the rear mudguards (see " Removal and installation wheel arch liners and...

Removal and installation the front mudguard
1. Remove the front wheel and place the vehicle on secure supports. 2. Unscrew the three mudguard liner mounting nuts. NOTE: This is how the front mudguard...

Removal and installation the right rear mudguard
1. Remove the rear wheel and place the vehicle on secure supports. 2. Remove the three screws securing the side fender liner... 3. ...and the lower mounting...

Removal and installation the left rear mudguard
1. Remove the rear wheel and place the vehicle on secure supports. 2. Remove the three screws securing the side fender liner... 3. ...and the lower mounting...

Removal and installation the rear wheel mudguard
To remove the rear wheel mudguard, follow these steps:. 1. Unscrew the two mudguard mounting nuts... 2. ...and remove the mudguard. 3. Install the rear wheel...

Removal and installation the front wing
You will need: a wrench and a 10 mm socket head. 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the front mudguard liner (see "...

Removal and installation the air intake box grille
You will need: a 15 mm wrench, a 7 mm socket head, a plastic mounting blade, and a flat-blade screwdriver. The air intake box grille is removed if it is...

Removal and installation bonnet sound insulation
You will need a pin removal tool or a flat-blade screwdriver. 1. Open the hood and place it on the support. 2. Pry up the bonnet soundproofing mounting pin......
There is 2 commentary

Removal and installation the hood
You will need: a 13 mm wrench, pliers, and a marker. 1. Open the hood. 2. Disconnect the windshield washer pump hose from the fitting on the hood. 3. Squeeze...

Removal, installation and adjustment of the hood lock
You will need: a 13 mm wrench and pliers. 2. Remove the two hood lock mounting bolts... 3. ... move the lock away from the radiator frame and, squeezing the...

Removal and installation the hood lock drive
You will need: a 13 mm wrench, pliers, and a flat-blade screwdriver. 1. Remove the front bumper (see " Removal and installation the front bumper "). 2. Remove...

Removal and installation the fuel tank filler pipe hatch cover
You will need a flat-blade screwdriver. 1. Open the fuel tank filler cap. NOTE: The fuel filler door can only be opened when the doors are unlocked. 2. Press...

Removal and installation the fuel tank filler pipe hatch lock
You will need: 10 mm keys, TORX T20, flat-blade screwdriver. 1. Remove the right rear mudguard (see " Removal and installation wheel arch liners and mudguards...

Removal and installation exterior rearview mirrors
You will need: a 10 mm socket head, a plastic mounting blade or a flat-blade screwdriver. NOTE: This subsection shows the removal of the left outside rearview...

Windshield wiper blade replacement
1. Move the wiper arm away from the window, overcoming the force of the arm spring. 2. Squeeze the brush adapter latches... 3. ...turn the adapter with the...

Replacing windshield wiper arms
You will need a 15 mm wrench. 1. Open the hood and place it on the support. 2. Remove the protective cap of the nut securing the lever to the wiper linkage...

Removal and installation the windshield wiper linkage assembly with gear motor
You will need a 10 mm socket head. 1. Remove the windshield wiper arms (see " Replacing windshield wiper arms "). 2. Remove the air intake box grille (see "...

Removal and installation the battery mounting shelf
You will need: a 13 mm socket head and a flat-blade screwdriver. The battery mounting shelf is removed for replacement if it is damaged and to gain access to...

This section is available at russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share information: