Exterior elements of the car body Chevrolet Tahoe 2

Front Bumper Bracket — Removal and Installation
Series 1500 1. Remove all associated panels and parts. 2. Remove the damaged bumper bracket. Warning: Do not remove material from the end of the frame rail. 3....

Front bumper — removal and installation
Removal 1. Remove the radiator grille. 2. If equipped, disconnect the fog light wiring connectors. 3. Loosen the bolts (1) and (2) securing the front bumper....

Front Bumper Panel — Removal and Installation
Avalanche 1. Raise the vehicle. 2. Unscrew the bolt of the front bumper stiffener. 3. Remove the fasteners (2) from the panel (1). 4. Remove the headlights and...

Front bumper air deflector
Removal 1. Raise the vehicle. 2. If installed, disconnect the fog light connectors. 3. Remove the fog lights. 4. Using a flat-head screwdriver, loosen the...

Front bumper stiffener (Avalanche)
Removal 1. Loosen the bolt (2) securing the stiffener to the bumper panel trim. Tightening torque 15 Nm. 2. Loosen the bolt (3) securing the stiffener to the...

Rear bumper — removal and installation
Removal 1. Disconnect the license plate light connector. 2. Unscrew the nut (1) of the bumper reinforcement. 3. Unscrew the nuts (2) of the bumper mounting...

Rear Bumper Panel — Removal and Installation
Removal 1. Remove the upper bumper panel fasteners. 2. Disconnect the license plate light connectors. 3. Raise the vehicle and place safety posts under the...

Radiator grille — removal and installation
Avalanche 1. Open the hood. 2. Remove the fasteners (1) from the grille on the radiator support. 3. Pull the grille out of the radiator support reinforcement....

Radiator grille protection
Removal 1. Unscrew the bolts (1) and nuts (2) securing the front side protection (3). 2. Remove the front side protection. 3. Open the hood. 4. Remove the...

Front wing — removal and installation
Note: The procedure for replacing the left wing is shown here, replacing the right wing is similar, except for some minor differences. 1. Disconnect the...

Hood — removal and installation
Removal Caution: When removing and installing the hood support support in the open position, secure the hood with a temporary support to avoid injury or damage...

Soundproofing the hood — removal and installation
Removal 1. Open the hood. 2. Disconnect the engine compartment light connector. 3. Disconnect the clips securing the lamp wires to the hood. 4. Press the lamp...

Hood lock — removal and installation
Removal 1. Raise the hood. 2. Remove the upper radiator flap support. 3. Loosen the bolts (2) of the bonnet lock (1). Tightening torque 9 Nm. 4. Disconnect the...

Hood lock cable
Removal Caution: If the cable is broken, open the hood by pressing the lock lever on the left side with a suitable pin. 1. Raise the hood. 2. Remove the left...

Radiator support — removal and installation
Removal 1. Disconnect the negative battery cable. 2. Disable the passive safety system. 3. Remove the air intake duct. 4. Remove the air filter housing. 5....

Radiator grille reinforcement
Removal 1. Remove the headlights. 2. Remove the turn signal bulbs. 3. Remove the radiator grille. 4. Remove the front bumper cover. 5. Loosen the bolts (3) and...

Upper radiator support brace
Removal 1. Disconnect the negative battery cable. 2. Remove the upper radiator shutter. 3. Remove the headlights. 4. Remove the upper air conditioner condenser...

This section is available at russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share information:

Tahoe 2 and 3 (2000-2014)