Doors, locks and windows of the car Chevrolet Tahoe 2

Door component arrangement
Driver's door. 1 - door frame, 2 - door control unit, 3 - rear view mirror, 4 - window lifter motor, 5 - seat heating switch connector, 6 - door illumination...

Adjusting the door position
Please note: this procedure can only be performed with bolted door hinges. 1. Loosen the latch mounting bolt. 2. Loosen the bolts securing the door hinges to...

Front door — removal and installation
Removal 1. Remove the door trim panel. 2. Remove the outside mirror. 3. Remove the window glass. 4. Remove the window lift mechanism. 5. Remove the inner door...

Front door trim panel
Removal 1. Remove the inner door handle cover. 2. Remove the upper door trim panel extension. 3. Using a flat-head screwdriver, carefully remove the door lock...

Front door hinge — on pillar
Removal 1. Remove all hinge related panels and parts. 2. Remove excess sealant around the hinge and use a scriber to draw the outline of the hinge installation...

Front door hinge — on the door
Removal 1. Remove all hinge related panels and parts. 2. Remove excess sealant around the hinge and use a scriber to draw the outline of the hinge installation...

External rear view mirror
Removal 1. Remove the front door trim panel upper extension. 2. If the mirror is electrically operated, disconnect the mirror wiring connector. 3. Loosen the...

Interior trim of the external rear view mirror
Removal 1. Open the front door. 2. Pull the top edge of the trim towards you until it releases from the clips. 3. Lift the trim up until it exits the door trim...

Rear side door
Removal 1. Remove the door trim panel. 2. Remove the window lift mechanism. 3. Remove the inner door handle. 4. Remove the outer door handle. 5. Remove the...

Rear side door trim panel
Removal 1. Remove the inner door handle cover. 2. Remove the window lift handle (if installed). 3. Using a flat-head screwdriver, carefully remove the door...

Door opening limiter
Removal 1. Open the door. 2. Remove the door trim panel. 3. Remove the door seal. 4. Loosen the limiter mounting bolt to the body. Tightening torque 25 Nm. 5....

Interior door handle
Removal 1. Remove the door trim panel. 2. Loosen the inner door handle mounting bolts. Tightening torque 9 Nm. 3. Slide the inside door handle forward until it...

External door handle
Removal 1. Remove the door trim panel. 2. Remove the door seal. 3. Disconnect the lock rod from the handle. 4. Disconnect the rod from the door lock cylinder....

Door lock drive
Removal Note: here are instructions for replacing the front door lock, replacing the rear door lock drive is carried out in a similar way. 1. Raise the window...

Door window lifter — removal and installation
Removal 1. Raise and secure the glass. 2. Remove the door trim panel. 3. Remove the door seal. 4. Disconnect the window lift motor wiring connector. 5. Unscrew...

Rear side door window switch
Removal 1. Using a small flat-blade screwdriver, carefully pry the switch out of the door trim panel. 2. Disconnect the switch connector. Installation 3....

Door lock latch
Removal Warning: If both latch mounting bolts are removed at the same time, the latch reinforcement plate will fall into the body cavity. This will result in...

Control unit in the door
Removal and installation 1. Remove the door trim panel. 2. Disconnect the wiring connectors. 3. Loosen the screw (2) securing the switch cover (1) to the door...

Door Trim Panel Insert (Escalade)
Removal 1. Remove the door trim panel. 2. Unscrew the nuts (1) of the door trim insert. Front door Rear side door 3. Remove the door trim panel insert....

Electric window lift motor
Removal 1. Raise the window. If the window motor does not work, remove the window to gain access to the motor mounting screws. 2. Remove the door trim panel....

Door glass — removal and installation
Removal 1. Partially raise the glass. 2. On the front door, remove the upper door trim panel extension. 3. Remove the manual door lock lever. 4. Remove the...

Glass guide channel
Removal 1. Remove the glass. 2. Remove the glass seal. Front door 3. Unscrew the glass guide channel mounting bolts. Tightening torque 9 Nm. 4. Remove the...

Cargo compartment door (composite)
Removal 1. Disconnect the negative battery cable. 2. Apply protective tape around the perimeter of the door and body pillar. 3. Remove the tail lights. 4....

Rear cargo door (one piece)
Removal 1. Open the door. 2. Place a temporary support under the door. 3. Remove the rear roof end molding. 4. Disconnect the door wiring connectors. 5....

Rear cargo door trim panel
Removal 1. Remove the top trim panel. 2. Remove the inner closure loop (only solid door). 3. Slide the trim panel up until it comes off the retaining hooks....

Rear cargo door glass
Removal 1. Raise the glass. 2. Place a temporary support under the glass. 3. Disconnect the glass heater connector. 4. Remove the glass support posts. 5. Open...

Rear cargo compartment door lock actuator
Removal 1. Remove the upper and lower door trim panels. 2. Disconnect the door wiring connectors. 3. Disconnect the lock control cables from the drive. 4....

Rear cargo door lock cylinder
Removal 1. Remove the door trim panel. 2. Remove the door window lock. 3. Press the lock cylinder release. 4. Turn the lock cylinder counterclockwise. 5....

Rear door lock
Removal 1. Loosen the bolts (2) securing the lock. Tightening torque 25 Nm. 2. Remove the lock (4). 3. Disconnect the lock wiring connector. 4. Disconnect the...

Fuel tank filler flap
Removal 1. Open the fuel tank filler cap. 2. Loosen the filler neck mounting screws. Tightening torque 9 Nm. 3. Remove the filler neck fasteners. 4. Move the...

Pressure relief valve
Removal 1. Open the cargo compartment door. 2. Remove the rear fender outer panel trim. 3. Remove the upper rear molding. 4. Remove the rear corner molding. 5....

Rear side of the cargo compartment
Removal 1. Lower the tailgate of the cargo platform. 2. Remove the side panel anti-theft bolt. Tightening torque 25 Nm. 3. With the help of an assistant, raise...

Tailgate handle for cargo area
Removal 1. Remove the tailgate handle cover, see "Adjustment". 2. Release the lock rod retainers on both sides of the trim, see "Adjustment". 3. Unscrew the...

Tailgate lock for cargo compartment
Removal 1. Lower the tailgate. 2. Loosen the lock handle bolts. Tightening torque 25 Nm. 3. Raise the tailgate. 4. Remove the handle cover by prying it up at...

Tailgate lock cylinder for cargo area
Removal 1. Open the cargo compartment roof. 2. Press the spring-loaded lock catch. 3. Turn the lock cylinder a quarter turn clockwise. 4. Remove the lock...

Lower cargo door hinge
Removal 1. Restore as much as possible of all damage sustained in the accident. 2. Remove all associated panels and parts. 3. Clean the area around the hinge...

Upper cargo door hinge
Removal 1. Repair all damage as completely as possible. 2. Remove all associated panels and parts. 3. Clean the area around the hinge from excess sealant. 4....

Cargo Compartment Door Lock Handle
Removal 1. Remove the door trim panel. 2. Pull back the door seal. 3. Disconnect the lower door lock opening cable from the handle. 4. Loosen the handle...

Cargo Compartment Composite Door Lock Drive
Removal 1. Remove the door trim panel. 2. Remove the door seal. 3. Remove the lock drive rod. 4. Disconnect the drive wiring connector. 5. Remove the lock...

Lock rod and outer handle of the composite cargo compartment door
Removal 1. Remove the door trim panel if necessary. 2. Remove the door seal if necessary. 3. Remove the traction lock clip from the lock. 4. Unscrew the nuts...

Lower cargo door lock
Removal 1. Loosen the bolts securing the lock to the door. Tightening torque 25 Nm. 2. If installed, disconnect the lock wiring connector. 3. Disconnect the...

Upper cargo door lock
Removal 1. Remove the door trim panel. 2. Unscrew the bolts securing the lock to the door. 3. Remove the lock from the door. 4. Disconnect the lock release...

Middle door panel
Removal 1. Fold down the rear seat back. 2. Remove the hinges of the middle door. 3. Open the middle door, leaving the glass in place. 4. Remove the middle...

Middle door hinges
Removal 1. Fold down the rear seat back. 2. Make sure the middle door (pickup truck model cab rear door) raised and locked. 3. Remove the hinge cover (1). 4....

Middle door latch
Removal 1. Fold the rear seat. 2. Remove the middle door panel. 3. Open the middle door. 4. Loosen the latch mounting bolt. Tightening torque 9 Nm. 5. Remove...

Cargo Compartment Floor Trim Plate
Removal Avalanche/Escalade EXT 1. Remove the third pillar trim. 2. Remove the hinges of the middle door. 3. Remove the floor trim plate (1). Installation 4....

Cargo compartment lid guide
Removal 1. Lower the rear cargo area door. 2. Remove the cargo compartment cover. 3. Remove the auxiliary handle. 4. Remove the upper drainage channel. 5....

Cargo Compartment Door Removable Window Lock
Removal 1. Remove the removable window panel. 2. Remove the trim panel (1) from the rear of the ceiling panel. 3. Loosen the lock mounting bolts. Tightening...

Central cargo bay bridge
Removal Avalanche 1. Turn off the headlights. 2. Remove the cargo compartment cover. 3. Loosen the screws (1) and (2) securing the central bridge. Tightening...

Side bridge of the cargo compartment
Removal Avalanche and Escalade EXT 1. Remove the cargo compartment cover. 2. Remove the cargo compartment center bridge. 3. Loosen the screws (1) securing the...

Removal and installation of frame elements
Front engine mount cross member 1. Raise the vehicle and place safety posts under the frame. 2. Remove the front axle main gear housing guard. 3. Loosen the...

Installation of stationary glass
Warning: When working with glass or sheet metal with rough edges, wear safety glasses and gloves. If the glass is cracked but still holds together, tape the...

Rear wing glass
Removal 1. Open the cargo door. Caution: If glass fragments get into the defroster vents, they may be blown out and cause injury to the passenger. 2. Close the...

Molding of stationary glass openings
Removal Note: The window opening molding fills the cavity between the body and the glass. If the molding is damaged, it must be replaced. The molding cannot be...

Windshield — Removal and Installation
Removal 1. If installed, remove the fixed antenna mast. 2. Open the hood. 3. Remove the wiper arms. 4. Remove the air intake grille. 5. Move the front door...

Washer pump and reservoir
Removal 1. Remove the battery and its tray. 2. Remove the fender liner. 3. Disconnect the washer pump wiring connector. 4. Disconnect the washer fluid level...

Windshield wiper motor and linkage
Removal 1. Remove the wiper arms. 2. Remove the air intake grille. 3. Loosen the four mounting bolts and remove the amplifier panel. Tightening torque 9 Nm. 4....

Windshield wiper lever
Removal 1. Using masking tape, mark the position of the wiper blade on the windshield. 2. Disconnect the washer hose. 3. Remove the lever mounting nut cover....

Wiper Motor Cover
Removal 1. Turn off the ignition. 2. Open the hood. 3. Remove the radio antenna. 4. Remove the wiper arms. 5. Remove the air intake grille. 6. Remove the...

Rear window wiper motor
Removal 1. Remove the wiper arm. 2. Unscrew the nut and remove the spacer from the electric motor shaft. Tightening torque 8 Nm. 3. Remove the cargo door trim...

Rear window wiper lever
Removal 1. Disconnect the washer hose. 2. Remove the wiper arm nut cover. 3. Unscrew the nut securing the lever to the electric motor shaft. Tightening torque...

Sunroof — Position adjustment
The adjustment is carried out with the hatch in the zero (closed) position. Warning: Do not remove the sunroof drive mechanism screws. 1. Loosen the 4...

Roof drainage channel
Removal 1. Remove the sunroof glass panel. 2. On one side of the drain channel (1), press the key (3) back and lift the drain channel. Do the same on the other...

Sunroof Tie Rods
Removal Note: The connecting rods and other parts required for replacement are included in the repair kit. 1. Remove the sunroof window. 2. Remove the roof...

Sunroof Drain Hose
Removal Front hose 1. Remove the windshield opening panel. 2. Remove the sun blinds. 3. Pull down the corner of the ceiling panel. 4. Remove the hose from the...

Sunroof glass
Removal 1. Pull back the sunroof curtain. 2. Set the hatch to the closed position. 3. From the passenger compartment, unscrew the four adjustment screws of the...

Sunroof Curtain — Removal and Installation
Removal 1. Remove the sunroof glass. 2. Remove the roof drainage channel. 3. With the curtain (1) in the closed position, press the front (from any side)...

Sunroof frame
Removal 1. Remove the sunroof glass. 2. Remove the decorative trim from the hatch. 3. Remove the ceiling panel. 4. Remove the sunroof curtain. 5. Remove the...

Hatch drive electric motor
Removal 1. Remove the ceiling panel. 2. Disconnect the sunroof drive motor wiring connector. 3. Loosen the two screws securing the electric motor. Tightening...

Sunroof Wiring
Removal 1. Remove the ceiling panel. 2. Disconnect connectors (5) and (6). 3. Remove the sunroof wiring. Installation Caution: Strictly adhere to the wiring...

Sunroof drive switch
Removal 1. Remove the overhead console. 2. Disconnect the wiring connector. 3. Unclip the switch and remove it from the console. Installation 4. Installation...

This section is available at russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share information:

Tahoe 2 and 3 (2000-2014)