Electrical appliances (since 2007) of car Chevrolet Tahoe 2 and 3

Relays and Fuses
Location of fuses and relays (mounting block in the engine compartment) Table. Location of fuses and relays (mounting block in the engine compartment)...

Removal and installation the mounting block in the engine compartment
1. Disconnect the cable from the negative terminal of the battery. 2. Remove the cover from the mounting block. 3. Disconnect the clips and remove the engine...

Removal and installation the mounting block bracket in the engine compartment
1. Remove the mounting block in the engine compartment. 2. Loosen the screws (1). Tightening torque 9 Nm. 3. Remove the mounting block bracket in the engine...

Removal and installation the mounting block under the instrument panel (left side)
1. Remove the knee support. 2. Disconnect all connectors. 3. Disconnect the clips and remove the mounting block under the instrument panel (1). 4. Install in...

Removal and installation the mounting block under the instrument panel
1. Remove the cover. 2. Disconnect the connectors and remove the mounting block (1). 3. Install in the reverse order of removal.

Removal and installation the instrument cluster
Escalade 1. Remove the instrument cluster bezel. 2. Loosen the screws (1). 3. Remove the instrument cluster (2). 4. Disconnect the connectors. Note: Before...

Removal and installation the trip computer control switch
Escalade 1. Remove the instrument panel center trim (1). 2. Remove the trip computer control switch (2). 3. Install in the reverse order of removal. Besides...

Removal and installation the watch
1. Remove the center instrument panel trim. 2. Disconnect the connector. 3. Squeeze the latches and remove the watch (1). 4. Install in the reverse order of...

Removal and installation the switch panel
Escalade 1. Remove the instrument panel center trim (1). 2. Loosen the screws (2). 3. Remove the switch panel (3). 4. Disconnect the connector. 5. Install in...

Removal and installation the windshield wiper control switch
1. Remove the steering wheel. 2. Remove the steering column cover. 3. Loosen the screws (1). Tightening torque 3 Nm. 4. Remove the windshield wiper and washer...

Removal and installation the windshield washer hose
1. Open the hood. 2. Remove the left front fender liner. 3. Disconnect the washer hose from the electric pump. 4. Disconnect the clamps (1). 5. Disconnect...

Removal and installation the washer reservoir
1. Place the vehicle on a lift. 2. Remove the left front wheel. 3. Remove the left front fender liner. 4. Disconnect the washer hoses (1, 2) and detach the...

Removal and installation the windshield washer electric pump
1. Remove the washer reservoir. 2. Using two slotted screwdrivers, remove the windshield washer pump (1). 3. Replace the rubber bushing (2). 4. Install in the...

Removal and installation the rear window washer electric pump
1. Remove the washer reservoir. 2. Using two slotted screwdrivers, remove the rear window washer pump (1). 3. Replace the rubber bushing. 4. Install in the...

Removal and installation the washer fluid level sensor
1. Remove the washer reservoir. 2. Using two slotted screwdrivers, remove the washer fluid level sensor (1). 3. Replace the rubber bushing (2). 4. Install in...

Removal and installation the washer fluid heater
1. Remove the left front fender liner. 2. Disconnect the outlet hose (1). 3. Disconnect the inlet hose (2) from the washer hose (3). 4. Disconnect the...

Removal and installation windshield wiper arms
1. Open the hood. 2. Unscrew the nut (1) and remove the washer (2). Tightening torque 35 Nm. 3. Turn the washer hose (3) clockwise. 4. Remove the lever (4). 5....

Removal and installation the rear window wiper arm
1. Lift the protective cap (1). 2. Unscrew the nut (2). Tightening torque 9 Nm. Note: When tightening the nut, hold the lever in the extreme position. 3. Turn...

Windshield wiper drive motor control circuit
1. Turn the ignition switch to the "OFF" position. 2. Open the hood. 3. Remove the antenna. 4. Remove the windshield wiper arms. 5. Remove the ventilation...

Windshield wiper drive motor
1. Remove the windshield wiper arms. 2. Remove the ventilation grille. 3. Loosen the four bolts and remove the spacer. Tightening torque 9 Nm. 4. Disconnect...

Rear window wiper drive motor
1. Remove the rear door trim. 2. Remove the rear window wiper arm. 3. Unscrew the nut from the outside and remove the gasket. 4. Loosen the bolts (1) securing...

Removal and installation the windshield wiper drive rod
1. Remove the windshield wiper arms. 2. Remove the ventilation grille. 3. Disconnect the connector. 4. Loosen the bolts (1). Tightening torque 9 Nm. 5. Remove...

Removal and installation the rain sensor
1. Disconnect the connector (2). 2. Remove the cover (1). 3. Disconnect the clips and remove the rain sensor (3). 4. Before installation, remove the old...

Main power window control switch
1. Disconnect the clamps (2). 2. Remove the main power window control switch (1). 3. Disconnect the connector. 4. Install in the reverse order of removal.

Passenger door window control switches
1. Disconnect the clamps (2). Front passenger door Rear side doors 2. Remove the main power window control switch (1). 3. Disconnect the connector. 4. Install...

Removal and installation window lift guides (front doors)
1. Set the glass to the position required for servicing. 2. Remove the door trim panel. 3. Remove the cover of the technological hole. 4. Secure the glass. 5....

Electric window lifter motor (front doors)
1. Set the glass to the position required for servicing. 2. Remove the door trim panel. 3. Remove the cover of the technological hole. 4. Disconnect the...

Removal and installation window lift guides (rear doors)
1. Deactivate the passive safety system. 2. Set the glass to the position required for servicing. 3. Remove the door trim panel. 4. Remove the cover of the...

Electric motor for window lift (rear doors)
1. Deactivate the passive safety system. 2. Set the glass to the position required for servicing. 3. Remove the guide. 4. Disconnect the connector. 5. Loosen...

Central locking remote control unit
Except Avalanche and Escalade EXT 1. Remove the rear pillar trim. 2. Disconnect the antenna connector (1). 3. Slide the central locking remote control unit (2)...

Replacing the battery in the transmitter
1. Insert a slotted screwdriver into the service hole in the area of the ring (5), between the two halves of the housing (6,4). 2. Turn the screwdriver and...

Removal and installation the sunroof drive electric motor
1. Remove the roof console. 2. Remove the hatch bracket. 3. Disconnect the connector (1). 4. Loosen the screws (2). Tightening torque 6 Nm. 5. Remove the...

Authorization procedure for the sunroof drive motor
Note: the authorization procedure is required in the following cases: A new sunroof drive motor has been installed. The sunroof drive motor was removed and...

Removal and installation the sunroof electric drive control switch
1. Remove the roof console (1). 2. Loosen the screws (2). 3. Disconnect the connector. 4. Remove the sunroof electric drive control switch (3). 5. Install in...

Removal and installation the rear door electric drive control unit
1. Remove the left side luggage compartment trim. 2. Disconnect the retainer (1). 3. Remove the rear door electric drive control unit (2). 4. Disconnect the...

Removal and installation the rear door drive motor
1. Remove the left side luggage compartment trim. 2. Remove the rear door electric drive rod. 3. Loosen the bolts (1). Tightening torque 8 Nm. 4. Disconnect...

Removal and installation the rear door electric drive rod
1. Remove the left side luggage compartment trim. 2. Disconnect the clips and remove the rear door electric drive rod (1). 3. Install in the reverse order of...

Removal and installation the rear door position sensor
1. Remove the rear door trim. 2. Disconnect the connector. 3. Disconnect the pistons (1). 4. Remove the rear door position sensor (2). 5. Install in the...

Removal and installation the rear door electric drive switch
1. Remove the left side luggage compartment trim. 2. Loosen the screw (1). 3. Disconnect the connector. 4. Remove the rear door electric drive switch (2)....

Removal and installation the rear door open sensor
1. Remove the rear door handle. 2. Loosen the screws (1). 3. Disconnect the connector. 4. Remove the rear door open sensor (2). 5. Install in the reverse order...

Removal and installation the rear door electric drive
1. Remove the left side luggage compartment trim. 2. Remove the rear door electric drive rod. 3. Disconnect the connector from the rear door electric drive...

Removal and installation of the electronic unit of the parking system
1. Remove the front passenger seat. 2. Unscrew the nuts (1). 3. Fold back the carpet. 4. Disconnect the connector. 5. Remove the parking system electronic unit...

Removal and installation parking system indicators
Tahoe, Suburban, Yukon and Yukon XL 1. Remove the rear pillar trim (1). 2. Loosen the screws (2). 3. Disconnect the connector. 4. Remove the parking system...

Removal and installation parking sensors
1. Remove the rear bumper bezel. 2. Disconnect the connector. 3. Lift the latches on the retainer and remove the parking sensor.

Removal and installation the rear view camera
Back door 1. Remove the rear door trim. 2. Loosen the screws (1). 3. Disconnect the connector. 4. Remove the rear view camera (2). 5. Install in the reverse...

Removal and installation the rear view camera unit
1. Remove the right front seat. 2. Unscrew the nuts (1). Tightening torque 2 Nm. 3. Disconnect the connector. 4. Remove the rear view camera unit (2). 5....

This section is available at russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share information:

Tahoe 2 and 3 (2000-2014)