Car clutch repair Chevrolet Tahoe 1

Technical data (gaps and dimensions in mm)
General information The permissible thickness of the friction disc linings is 1.5 Tightening torques for connections (Nm) Clutch Bolts securing the pressure...

Clutch — description and testing
1. The clutch on the vehicles in question is dry, single-disc, diaphragm type with hydraulic drive (see photo). 2. It is recommended to perform the following...

Clutch Master Cylinder — Removal and Installation
Attention! 1. The cylinder of the dismountable design is installed only on models before 1992. Since 1993, non-dismountable master clutch cylinders have been...

Clutch slave cylinder — removal, disassembly and installation
Attention! 1. The clutch slave cylinder of a dismountable design is installed only on models before 1992. Since 1993, non-dismountable clutch slave cylinders...

Clutch parts — removal, inspection and installation
1. Raise the front of the vehicle. 2. Remove the master cylinder. 3. Remove the clutch slave cylinder. 4. On a gearbox with a cast iron housing, unscrew the...

Release bearing — removal, inspection and installation
1. Disconnect the battery from ground. 2. Remove the gearbox. 3. On vehicles with a cast iron gearbox, remove the bell housing. 4. On pre-1995 models, remove...

Guide Bearing — Checking and Replacing
1. The pilot bearing is the support of the primary shaft of the gearbox and is pressed into the hole in the rear flange of the crankshaft. The condition of the...

Clutch hydraulic drive — air removal
1. Bleeding the system will be required every time after disassembling and assembling the clutch hydraulic line. 2. Fill the reservoir with fresh brake fluid...

Cardan shafts and cardan joints — general information
1. The vehicles in question are equipped with single-section or two-section cardan shafts with two or three (on all-wheel drive vehicles) cardan joints. 2. In...

Checking the cardan shafts
1. Raise the vehicle. 2. Inspect the cardan shafts. If there are dents, cracks or deformations, replace the shaft. 3. If traces of leakage are detected near...

Cardan shaft — removal and installation
1. Disconnect the battery from ground. Rear shaft 2. Raise the vehicle and support it on stands. Place the transmission in neutral. The parking brake should be...

Middle support of the propeller shaft — removal and installation
1. Remove the rear propeller shaft. 2. Unscrew the support mounting bolts. 3. Disconnect the driveshaft sections and remove the center support from the front...

Cardan joints — removal, disassembly and installation
Attention! The cardan joint repair kit must match the joint that is installed on this car model. 1. Remove the driveshaft. Cardan joints with external...

Half shafts — general information
The vehicles in question are equipped with two types of rear axles: fully unloaded and semi-unloaded. Semi-unloaded axles rest on the outer part on a roller...

Semi-unloaded rear axle half shaft — removal and installation
1. Raise the vehicle. Remove the rear wheel and brake drum. On models with a locking differential, remove both rear wheels and brake drums. 2. Remove the...

Axle shaft seal (semi-floating axle shaft) — replacement
1. Remove the axle shaft. 2. Pry and remove the seal from the end of the axle housing with a large screwdriver or the inside of the axle shaft (see photo). 3....

Rear axle bearing (semi-floating axle shaft) — replacement
1. Remove the axle shaft and remove the seal. 2. Remove the bearing from the axle housing using an impact puller (see photo). Press in the new bearing with a...

Fully unloaded axle shaft — removal and installation
1. Unscrew the bolts securing the axle shaft flange to the hub; you don't need to remove the wheel (photo). 2. Loosen the axle shaft by lightly tapping the...

Main gear shaft seal — replacement
1. Raise the rear of the vehicle and place it on stands. Block the front wheels. 2. Disconnect the propeller shaft, move it to the side and secure it. 3. If...

Rear axle — removal and installation
1. Raise the rear of the vehicle and place it on stands. Remove the rear wheels. 2. Support the rear axle under the gearbox housing with a trolley and jack. 3....

Brake Hub/Drum and Wheel Bearings — Removal, Installation and Adjustment
1. Remove the axle shaft. 2. Loosen the rear wheel nuts, raise the rear of the car and place it on stands. Block the front wheels and remove the rear wheels....

Front axle shaft (4WD models) — removal and installation
1. Remove the hub cap on the side from which the axle shaft is being removed. Loosen the wheel nuts. Loosen the hub nut 1/4 turn, then raise the car and place...

Replacing axle shaft covers and checking CV joints
1. Remove the axle shaft. If the axle shaft is equipped with a boot casing, cut off the clamps and remove the casing. 2. Place the axle shaft in a vice. Inner...

Front axle shaft with housing (all-wheel drive models) — removal and installation
Attention! In case of a leak in the seal or failure of the axle bearing, the housing assembly with the axle, bearing and seal should be removed and sent to a...

This section is available at russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share information:

Tahoe 2 and 3 (2000-2014)