Car steering Chevrolet Tahoe 2 and 3

Steering — General Information
Depending on the modification and year of manufacture, one of two types of steering mechanisms can be installed on the models: worm - ball nut; rack - sector....

Bleeding the power steering system
1. Make sure that there is no harmful contact between the system hoses and individual components of the vehicle. Caution: Contact with frame, body or engine...

Diagnostics of vacuum drop
1. If the vacuum continues to be released, disconnect the discharge and return hoses from the pump. 2. Plug the pump openings with suitable plugs. 3. Connect...

Power steering pump pulley
Removal 1. Remove the radiator fan diffuser (or just its upper part). 2. Remove the accessory drive belt. 3. Using a puller, remove the pump pulley....

Power steering pump
Power steering pump. 1 - power steering pump reservoir, 2 - reservoir cover, 3 - reservoir mounting stud, 4 - reservoir mounting stud, 5 - pump tube plug, 6 -...

Steering gear — removal and installation
Removal 1. Place a container for the fluid under the steering gear of the vehicle. 2. If the engine protection is installed, remove the protection. 3....

Adjusting the tension of the steering gear worm thrust bearing
Note: Adjustment is performed with the steering gear removed. 1. Using a special key, tighten the adjusting nut assembly until the thrust bearing is fully...

Adjusting the preload of the center position of the bipod shaft
Note: Adjustment is performed with the steering gear removed. 1. Loosen the lock nut (1) of the adjustment screw (2) of the bipod shaft. 2. Completely unscrew...

Steering rack — removal and installation
Steering rack assembly. 1 - outer tie rod, 2 - inner tie rod nut, 3 - boot clamp, 4 - boot, 5 - boot clamp, 6 - inner tie rod, 7 - rack cylinder tube, 8 - rack...

Adjusting the steering rack bearing preload
Note: adjustment is performed with the steering rack removed. 1. Loosen the lock nut of the steering rack bearing adjusting plug. Removing the steering rack...

Steering column — design description
Standard steering column with gear shift lever. 1 - Upper housing, 2 - Lower housing, 3 - Gear shift lever seal, 4 - Gear shift lever screw, 5 - Gear shift...

Steering column — removal and installation
Removal Caution: Read the warnings in the chapter " Passive safety system ". 1. Disable the passive safety system (airbags). 2. Remove the knee support. Note:...

Checking the steering column after a collision
The steering column should be checked if the following occurs after an accident: frame damage; major damage to the body; steering column hit; airbag...

Steering column covers
Removal Caution: Read the warnings in the chapter " Passive safety system ". 1. Disable the passive safety system (airbags). 2. Remove the steering wheel. 3....

Steering column boot
Removal and installation 1. Set the front wheels to the straight-ahead position. 2. Set the steering wheel to the locked position (LOCK ignition switch). 3....

Ignition switch — removal and installation
Removal Caution: Read the warnings in the chapter " Passive safety system ". 1. Disconnect the negative battery cable. 2. Disable the passive safety system. 3....

Steering wheel position sensor
Steering wheel position sensor. 1 - bolt, 2 - steering column bracket, 3 - sensor fixing clip, 4 - steering wheel position sensor. Removal Caution: Identify...

Airbag Current Collector
Note: The driver's airbag current collector must be placed in the central position during installation. Incorrect installation of the current collector may...

Lower intermediate steering shaft
Removal Warning: Please read the notes and warnings in the chapter " Passive safety system ". Note: Before disconnecting the steering shaft from the steering...

Upper intermediate steering shaft
Removal Warning: Please read the notes and warnings in the chapter " Passive safety system ". Note: Before disconnecting the steering shaft from the steering...

Steering rack boot
Removal 1. Remove the outer tie rod. 2. Unscrew the nut (2) securing the inner steering rod (1). 3. Remove the clamp (2) securing the steering rack boot (1)....

Pendulum arm — removal and installation
Removal Note: Do not use a wedge to separate the ball joints, as this may damage the joint boot. Use a special puller. 1. Raise the vehicle and place safety...

Outer tie rod
Removal 1. Raise the vehicle and place safety posts under the frame. Note: Do not use a wedge to separate the ball joints, as this may damage the joint boot....

Inner tie rod
Removal 1. Raise the vehicle and place safety posts under the frame. Note: Do not use a wedge to separate the ball joints, as this may damage the joint boot....

Steering shock absorber
Removal 1. Raise the vehicle and place safety posts under the frame. 2. If the engine protection is installed, remove the protection. 3. Loosen the nut (1) of...

Transverse steering rod
Removal 1. Raise the vehicle and place safety posts under the frame. 2. If the engine protection is installed, remove the protection. 3. Separate the steering...

This section is available at russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share information:

Tahoe 2 and 3 (2000-2014)