Electrical equipment and devices of the car Chevrolet Aveo 2 (T300)

Features of the design of electrical equipment of the car
The electrical equipment of the car is made according to a single-wire scheme: the negative terminals of the sources and consumers of electric power are...

Diagnostics of faults of on-board electrical equipment
A typical electrical circuit may include a main electrical component, various switches, relays, electric motors, fuses, fusible links or circuit breakers...

Location of fuses, fuse links and their replacement
Most of the power circuits of the vehicle's electrical equipment are protected by fuses. Headlights, fan motors, fuel pump and other powerful consumers of...

Checking the ignition switch (lock)
The ignition switch (lock) with a mechanical locking device and an electrical contact part is located on the right side of the steering column under the...

Replacing the ignition switch (lock) contact group
You will need: flat- and Phillips-head screwdrivers, a special plastic mounting blade, and a TORX T20 key. 1. Disconnect the wire from the negative terminal of...

Replacing the ignition switch (lock) cylinder
You will need: a Phillips-head screwdriver, a special plastic mounting spatula, a thin metal rod (for example, a drill). 1. Disconnect the wire from the...

Removal and installation the ignition switch (lock)
You will need: TORX T20, TORX T50 keys, a Phillips-head screwdriver, a special plastic mounting blade, a drill with a 6 mm diameter drill, a new self-tapping...

Features of the design of lighting, light and sound signaling
Headlights Chevrolet Aveo cars are equipped with block headlights (figure 10.5), combining low and high beam headlights (with single-filament lamps), side...

Checking and adjusting headlights
You will need: a 6 mm Allen key or a Phillips-head screwdriver. Check and adjust the headlights on a loaded vehicle (with a full fuel tank, tool kit and spare...

Replacing the bulbs in the headlight
To replace the bulbs in the headlight unit, perform the following steps. 1. Open the hood and disconnect the wire from the negative terminal of the battery....

Replacing the side light bulb
To replace the side turn signal light bulb, follow these steps. 1. Move the turn signal light forward... 2. ...and remove it from the wing. 3. Turn the bulb...

Replacing the bulbs in the rear light
To replace any bulb in the rear light, follow these steps. NOTE: The work is shown on the example of a car with a sedan body. On a car with a hatchback body...

Replacing the license plate light bulb
To replace the license plate light bulb, follow these steps:. 1. Disconnect the wire from the negative terminal of the battery. 2. Press the lamp housing in...

Replacing the interior light bulb
To replace the interior light bulb, you need to remove the light from the roof trim panel. However, this can damage the plastic clips of the light and scratch...

Replacement of the trunk light bulb
To replace the trunk light bulb, follow these steps:. NOTE: The work is shown on a sedan car. On a hatchback car, the work is performed in the same way......

Removal and installation of the body electrical equipment control unit
You will need: flat-head and Phillips-head screwdrivers. 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the lower decorative panel...

Headlight replacement
You will need: TORX T20 key, socket heads "7", "10", plastic mounting blade, flat-blade screwdriver. 1. Disconnect the wire from the negative terminal of the...

Replacing the side turn signal light
1. Disconnect the wire from the negative terminal of the battery. 2. Move the turn signal light forward... 3. ...and remove it from the wing. 4. Turn the bulb...

Replacing the rear light
NOTE: The work is shown on the example of a car with a sedan body. On a car with a hatchback body (the only difference is the shape of the lantern) the work is...

Replacing an additional brake light
You will need: a 10 mm spanner, a special plastic mounting blade or a flat-blade screwdriver. NOTE: The work is shown on the example of a car with a sedan...

Replacing license plate lights
You will need a special plastic mounting spatula or a flat-blade screwdriver. The license plate lights are installed on the trunk lid (sedan) or tailgate...

Removal and installation the interior light
You will need a special plastic mounting spatula or a flat-blade screwdriver. you need to remove the lampshade from the roof trim trim, but this can damage the...

Replacement of the trunk light
You will need a special plastic mounting spatula or a flat-blade screwdriver. NOTE: The work is shown on a sedan car. On a hatchback car, this work is...

Replacing steering column switches
You will need: TORX T20 key, flat-blade screwdriver. 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the bottom... 3. ...and the...

Replacing the steering column switches with connector
If necessary, you can remove the steering column switches together with the connector. To do this, perform the following work. 1. Disconnect the wire from the...

Replacing the headlight corrector regulator
Regulator A of the electric headlight corrector is built into the external lighting control unit and forms a non-separable unit with it. If it is necessary to...

Removal and installation the horn
You will need: keys "10", "13", TORX T20, a screwdriver with a flat blade. The horn is installed in the left front wing arch (bottom view with the fender liner...

Removal and installation the windshield wiper motor reducer
You will need: keys "10", "13", "22", TORX T30, pliers. 1. Remove the windshield wiper arms (see " Replacing windshield wiper arms "). 2. Remove the air intake...

Removal and installation the washer reservoir
You will need: keys "10", "13", TORX T20, a screwdriver with a flat blade. The washer reservoir is installed in the arch of the left front wing (bottom view...

Removal and installation the washer pump
You will need: 10 mm keys, TORX T20, flat-blade screwdriver. 1. Remove the left front fender liner (see " Removal and installation wheel arch liners and...

Replacing the central control unit for electric windows
You will need: a 7 mm socket head, a TORX T20 key, a plastic mounting blade, and a flat-blade screwdriver. 1. Disconnect the wire from the negative terminal of...

Replacing the right front and rear door window lifter control switches
You will need: a 7 mm socket head, a TORX T20 key, a plastic mounting blade, and a flat-blade screwdriver. NOTE: The work is shown using the left rear door as...

Replacing the front door window lift motor
You will need: a 7 mm socket head, a TORX T20 key, a plastic mounting blade, and flat- and Phillips-head screwdrivers. NOTE: The work is shown using the left...

Replacing the rear door window lift motor
You will need: a 7 mm socket head, a TORX T20 key, a plastic mounting blade, and flat- and Phillips-head screwdrivers. NOTE: The work is shown using the left...

Replacing the joystick for controlling the outside mirrors
You will need: a 7 mm socket head, a plastic mounting blade, and a flat-blade screwdriver. 1. Disconnect the wire from the negative terminal of the battery. 2....

Removal and installation of the electric motor of the radiator fan of the engine cooling system
You will need: TORX T25 key, flat-blade screwdriver. 1. Remove the electric fan of the engine cooling system together with the casing (see " Removal and...

Features of the instrument cluster design
All the vehicle's control devices are combined into a cluster of devices. It includes a tachometer, control and signal lamps, and a display that shows the...

Removal and installation the instrument cluster
You will need: a 7 mm spanner, a special plastic mounting blade, and a flat-blade screwdriver. 1. Disconnect the wire from the negative terminal of the...

Replacement of the control unit for external lighting and headlight corrector
1. Disconnect the wire from the negative terminal of the battery. 2. Remove the fuse box cover. 3. From the inside of the panel, push out the switch block......

Hazard warning lights, central locking and front passenger airbag switches
You will need: a special plastic mounting spatula, flat-head and Phillips-head screwdrivers. 1. Disconnect the wire from the negative terminal of the battery....

Removal and installation the head unit of the audio system
You will need: a 7 mm spanner, a special plastic mounting blade or a flat-blade screwdriver. 1. Disconnect the wire from the negative terminal of the battery....

Removal and installation speakers
For removal full-range speakers in the front doors perform the following operations. You will need: a 7 mm socket head, a plastic mounting blade, and a...

Removal and installation the USB connector
You will need: socket heads "7", "10", screwdrivers with flat and Phillips blades, a plastic mounting blade. 1. Remove the right instrument panel trim panel...

Removal and installation control units on the steering wheel
You will need a TORX T20 key. 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the driver's airbag module (see " Removal and...

Removal and installation the immobilizer control unit
You will need: a Phillips-head screwdriver, a special plastic mounting spatula, a thin metal rod (for example, a drill). 1. Disconnect the wire from the...

Replacing the oil pressure warning light sensor
You will need: a 24 mm socket wrench and an extension. The oil pressure warning light sensor is screwed into the cylinder block wall on the left front side of...

Replacing the fuel level indicator sensor
You will need: a 10 mm wrench, 10 mm and 13 mm socket heads, a flat-blade screwdriver, pliers, and a container for draining fuel from the fuel pump module. The...

Replacing the parking brake indicator light switch
You will need: a 7 mm socket head, a TORX T25 key, a plastic mounting blade, and a flat-blade screwdriver. 1. Disconnect the wire from the negative terminal of...

This section is available at russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share information: