Adjusting the position of the front seats
1. Adjustment of the longitudinal position of the front seats. Depending on the vehicle configuration, the adjustment of the front seats can be carried out either mechanically or with the help of an electric drive.
a) On non-electric models, to adjust the longitudinal position of the front seats, move the lever up and move the seat to the desired position.
After adjustment, return the adjustment lever to its original position.
b) On models with electric drive, to adjust the longitudinal position of the front seats, move the switch in the direction of the desired movement, as shown in the illustration.
2. Adjusting the position of the front seat backrests.
a) On non-electric models, to change the angle of the seatback, lean forward slightly, pull up on the seatback locking lever, then lean back to the desired position and release the lever. The seatback will lock in this position.
b) On models with power seatback angle adjustment, move the switch to the desired position as shown in the illustration.
3. Adjustment of lumbar support and lateral support of the seat back.
The lumbar support and lateral support of the seat back are adjusted using a switch located on the side of the seat back. Pressing the front or back of the switch will adjust the lumbar support; pressing the top or bottom of the switch will change the stiffness of the lateral support of the seat back.
4. Adjusting the position of the headrest.
The headrest can be adjusted by moving it forward or backward as shown in the figure.
To raise the headrest, pull it up. To lower the headrest, release the lock by pressing the lock, and then lower the headrest down.
Access to the third row of seats or increase luggage space
To access the third row of seats (disembarkation and embarkation of passengers) or to increase the luggage space, you need to fold the second row seat according to the seat type.
Second row seat 40:60
1. Pull the loop located between the second row seat cushion and the backrest to lift the second row seat cushion.
2. Push the second row seatback towards the front seats and fold it down.
Note:
- When you fold the second row seatback, the seat headrests will automatically fold back.
- After passengers have boarded/disembarked from the third row of seats, return the second row seat to its original position).
Escalade ESV only
1. Pull the lever shown in the illustration up and fold the second row seatback.
2. Fold the seat back down.
3. Slide the seat forward until it locks into place.
Note: After passengers in the third row of seats have boarded/disembarked, return the second row seat to its original position.
Second row seat 50:50 (Chevrolet Tahoe, Cadillac Escalade)
1. Folding the seat back.
a) Pull lever "1" located at the rear of the seatback upward and fold the second row seatback.
b) To return the second row seat back to its original position, pull up the lever "1" and lift the seat back until it locks. To lift the back, you can use the auxiliary loop located on the side of the back.
2. Folding the seat.
a) Fold the seat back (see above).
b) Unlock the seat by pulling lever "2" located at the rear of the seat.
c) Lift the seat by the rear part of the seat cushion until it locks into place. The seat will then be locked in the upright position.
d) To return the seat to its original position:
- Pull lever "3" towards you.
- While holding lever "3", slowly lower the seat to a horizontal position.
- Make sure the seat is locked in the operating position, then raise the seat back (see above).
3. Removing the rear seat.
a) Open the back door.
b) Fold the seat (see above).
c) Press the lever shown in the figure and pull the seat up.
d) Holding the seat by the top, roll the seat out of the vehicle through the rear door.
d) To install the seat in place:
- Holding the seats by the top, install the front seat rollers into the seat bracket holes in the floor. Make sure the seat bracket locks engage.
- Lower the seat down and fold the backrest (see above).
Second row seat of solid type (Chevrolet Tahoe, Cadillac Escalade)
1. Folding the seat back.
a) To fold the second row seatback, pull up lever "1" and lower the seatback all the way down.
b) To return the seat back to its original position, pull up lever "1" and lift the back until it locks.
2. Folding the seat.
a) Fold the seat back (see above).
b) Unlock the seat by pulling lever "2" located at the rear of the seat.
c) Lift the seat by the rear of the seat cushion.
d) While holding the seat in the upright position, release the seat post from the locks and lower it down until it locks. The second row seat will then be secured in the upright position.
d) The seat is installed in its original position in the reverse order.
3. Removing the rear seat.
a) Open the back door.
b) Fold the seat (see above).
c) Pull the loop located at the bottom center of the seat cushion to release the seat from the floor.
d) Holding the top of the seat, roll it out of the vehicle.
d) To install the seat in place:
- Holding the seats by the top, install the front seat rollers into the seat bracket holes in the floor. Make sure the seat bracket locks engage.
- Lower the seat down and fold the backrest (see above).
Second row split seat (Chevrolet Tahoe, Cadillac Escalade)
1. Adjusting the position of the seat back.
To change the angle of the seatback, lean forward slightly, pull up on the seatback locking lever, then lean back to the desired position and release the lever. The seatback will lock in this position.
2. Folding the seat back.
a) Pull the loop located between the second row seat cushion and the backrest to lift the second row seat cushion.
b) Pull up the seatback locking lever and lower the seatback all the way down.
[The original text can be found on the website: «ChevyMan»]