1. Remove the suspension arm (see the relevant section).
2. Place the suspension arm in a vice.
3. Drill out the rivets securing the ball joint to the lever.
4. Install the new ball joint on the control arm and tighten the bolts and nuts. Tightening torque 70 N·m.
5. Install the suspension arm (see the relevant section).
[The original article is on the website «ChevyMan»]
Front suspension ball joints (Chevrolet Tahoe 2)
The article was checked: Vladimir Romannikov
This article is available at russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Share information:
Previous articles
Tahoe 2 and 3: Car suspension
Next articles
See similar articles on the topic of Chevrolet cars:
Replacing the front suspension ball joint Chevrolet Aveo T300 (2012-2018)
Ball joint of the front suspension arm Chevrolet Captiva 1 (2006-2018)
Replacing the front suspension ball joint Chevrolet Cruze 1 (2008-2016)
Front suspension device Chevrolet Lacetti 1 (2002-2009)
Replacing the silent block and cushion of the front suspension arm Chevrolet Lanos T150 (2002-2009)
Front suspension device Chevrolet Niva 1 (2002-2016)
Removal and installation front suspension arms Chevrolet Lumina 1 (1989-1994)
Replacing the front suspension ball joint Chevrolet Aveo T300 (2012-2018)
Ball joint of the front suspension arm Chevrolet Captiva 1 (2006-2018)
Replacing the front suspension ball joint Chevrolet Cruze 1 (2008-2016)
Front suspension device Chevrolet Lacetti 1 (2002-2009)
Replacing the silent block and cushion of the front suspension arm Chevrolet Lanos T150 (2002-2009)
Front suspension device Chevrolet Niva 1 (2002-2016)
Removal and installation front suspension arms Chevrolet Lumina 1 (1989-1994)
Link in different formats to this page
Visitor comments
No comments yet
- General information
- Vehicle characteristics
- Vehicle device
- Manual
- Maintenance
- Power unit
- Engine repair
- Engine overhaul
- Cooling system
- Injection and control system
- Exhaust system
- Engine electrical equipment
- Transmission
- Automatic gearbox 4L60, 4L65, 4L70
- Automatic gearbox 6L50, 6L80, 6L90
- Transfer case
- Drive shafts and cardan
- Front drive axle
- Rear drive axle
- Chassis
- Car suspension
- Steering
- Brake system
- Body (until 2007)
- Exterior (external elements)
- Interior (internal elements)
- Doors, locks and windows
- Heating and air conditioning
- Security System (SRS)
- Body (since 2007)
- Exterior (external elements)
- Doors, locks and windows
- Interior (internal elements)
- Electrical equipment
- Electrical appliances (until 2007)
- Lighting and lamps (until 2007)
- Audio system (until 2007)
- Electrical appliances (since 2007)
- Lighting and lamps (since 2007)
- Audio system (since 2007)
- Wiring diagrams (2000-2005)
- Wiring diagrams (2005-2007)
- Wiring diagrams (since 2007)
- General information
- User manual
- Maintenance
- Power unit
- Engine in a car
- Engine removed
- Cooling system
- Heating and air conditioning
- Fuel and exhaust systems
- Decreased toxicity
- Transmission
- Manual gearbox
- Automatic gearbox
- Transfer case
- Clutch and drive shafts
- Chassis
- Brake system
- Car suspension
- Steering
- Body
- Repair of body elements
- Electrical equipment
- Engine electrics
- Equipment and devices
- Electrical circuits