Engine. Top view, late models. 1 - Fuel injector #6, 2 - Ignition coil #8, 3 - Fuel injector #8, 4 - Fuel injector #7, 5 - Ignition coil #7, 6 - Fuel injector #5, 7 - Ignition coil #5, 8 - Ignition coil #3, 9 - Fuel injector #3, 10 - Ignition coil #1, 11 - Fuel injector #1, 12 - Manifold Absolute Pressure Sensor, 13 - Fuel injector #4, 14 - Ignition coil #4, 15 - Ignition coil #2, 16 - Fuel injector #2, 17 - Ignition coil №6
Right side of engine, late models. 1 - ignition coil #8, 2 - ignition coil #6, 3 - ignition coil #4, 4 - absolute air pressure sensor in the intake manifold, 5 - throttle body, 6 - ignition coil #2, 7 - knock sensor #2, 8 - oil level sensor, 9 - starter, 10 - oil manifold of the cylinder deactivation system (if installed), 11 - Engine oil pressure sensor
Engine (front view, late models). 1 - throttle body, 2-absolute air pressure sensor in the intake manifold, 3-fuel vapor battery cleaning valve, 4-knock sensor No.1, 5 - coolant heater, 6-coolant temperature sensor, 7-camshaft position sensor, 8-generator
Right rear of the engine compartment (late models). 1 - Battery, 2 - Low pressure sensor in the air conditioning system, 3 - Air conditioning compressor clutch, 4 - Pressure switch in the air conditioning system, 5 - Mass air flow sensor / air temperature sensor
Left side of the engine compartment, (late models). 1 - windshield wiper motor, 2 - brake booster, 3 - windshield washer fluid heater (XA7), 4 - fuse box, 5 - engine control unit, 6 - automatic transmission control unit, 7 - brake booster vacuum sensor, 8 - brake fluid level sensor
Fuel system parts on chassis (late models, short wheelbase). 1 - frame, 2 - fuel vapor accumulator purge valve, 3 - fuel tank pressure sensor, 4 - fuel pump and fuel level sensor
Fuel system parts on chassis (late models, long wheelbase). 1 - fuel pump and fuel level sensor (primary), 2 - fuel tank pressure sensor, 3 - fuel pump and fuel level sensor (secondary, except NQZ), 4 - fuel vapor accumulator, 5 - fuel vapor accumulator purge valve, 6 - electronic suspension control unit
Assembling the pedals (later models except JF4). 1 - brake light switch, 2 - accelerator pedal position sensor
Assembling the pedals (late models, JF4). 1 - electronic pedal (JF4), 2 - brake light switch, 3 - accelerator pedal position sensor
Fuel pipes and hoses (late models)
Fuel vapor recovery system hoses (late models)
Left side of the engine, (early models). 1 - ignition coil #1, 2 - injector #1, 3 - injector #3, 4 - injector #5, 5 - injector #7, 6 - ignition coil #7, 7 - ignition coil #5, 8 - ignition coil #3, 9 - coolant temperature sensor
Right side of the engine (early models). 1 - ignition coil #8, 2 - injector wiring harness, 3 - injector #4, 4 - ignition coil #2, 5 - ignition coil #4, 6 - injector #6, 7 - ignition coil #6, 8 - injector #8
Knock sensors (early models). 1 - knock sensor #1, 2 - knock sensor #2
Engine. Top view (early models). 1 - absolute pressure sensor in the intake manifold, 2 - throttle body, 3 - fuel vapor accumulator solenoid valve
Oxygen sensors. Engine 5.3 l (early models). 1 - oxygen sensor (B1S2), 2 - oxygen sensor (B1S1), 3 - oxygen sensor installation location (B1S1), 4 - catalytic converter (B1), 5 - oxygen sensor installation location (B1S2), 6 - oxygen sensor installation location (B2S1), 7 - frame (right side), 8 - catalytic converter (B2), 9 - oxygen sensor installation location (B2S2), 10 - oxygen sensor (B2S2), 11 - oxygen sensor (B2S1)
Oxygen sensors. Engine 6.0 l (early models). 1 - oxygen sensor (B2S1), 2 - oxygen sensor installation location (B1S2), 3 - frame (right side), 4 - catalytic converter (B2), 5 - oxygen sensor (B2S2), 6 - installation location of the oxygen sensor (B2S2), 7 - catalytic converter (B1), 8 - oxygen sensor (B1S2), 9 - installation location of the oxygen sensor (B1S1), 10 - oxygen sensor (B1S1), 11 - installation location of the oxygen sensor (B2S1)
Note: Replacement parts must have the correct part number. Cases where the application of locking adhesive, lubricant, corrosion inhibitors or sealants to the threads during installation are specifically noted. Some new parts may be supplied with a coating already applied. Do not use coatings that are not recommended, this may affect the final tightening torque value, which in turn will affect the operation of the part or assembly. Strictly adhere to the recommended tightening torques during installation.
[The original source of the article is the website: «ChevyMan.ru»]