Brake system of the car Chevrolet Captiva 1

Technical characteristics of the hydraulic brake system
General technical characteristics Application Values Front brake discs Diameter 296 mm Thickness 29 mm Minimum allowable thickness 27.4 Lateral runout (in the...

Brake warning lamp electrical circuit
Brake warning lamp electrical circuit

Diagnostics of the hydraulic brake system
Checking the brake system The braking efficiency test should be performed on a flat, dry and clean road surface free of potholes. The test will not be truly...

Bleeding the hydraulic brake system (Manual)
Important: It is not possible to bleed the hydraulic modulator manually. If air has entered the ABS hydraulic modulator, or if an unfilled modulator is...

Rear wheel brake hose
Removal procedure 1. Raise and secure the vehicle. 2. Disconnect the brake pipe from the brake hose. 3. Remove the brake hose retaining clip and remove the...

Front wheel brake hose
Removal procedure 1. Raise and secure the vehicle. 2. Disconnect the brake pipe from the brake hose bracket on the wheel arches on both sides of the vehicle....

Brake light switch
Removal procedure 1. Rotate the brake light switch connector assembly and remove it from the brake pedal bracket. 2. Disconnect the brake light switch and...

Brake pedal — removal and installation
Removal procedure 1. Remove the trim panel from the instrument panel. 2. Remove the trim panel. See section 9E, "Instruments/Driver Information System". 3....

General description and operation of the brake master cylinder
Master cylinder The design of the master cylinder is intended for use in a braking system with a diagonal division of circuits. In the first circuit, servicing...

Master Cylinder Assembly — Removal and Installation
Removal procedure 1. Remove the bolts securing the brake fluid reservoir to the master cylinder and remove the reservoir from the master cylinder. 2. Remove...

Brake fluid reservoir
Removal procedure 1. Remove the pins securing the brake fluid reservoir to the master cylinder and remove the fluid level sensor by pressing on its support. 2....

General description and operation of the vacuum booster
Vacuum booster The vacuum booster uses a double diaphragm and a vacuum operating principle. In normal operation, when the brake pedal is not pressed, negative...

Vacuum hose — removal and installation
Removal procedure 1. Remove the clamp securing the vacuum hose to the brake booster. 2. Remove the hose from the brake booster. 3. Remove the clamp securing...

Vacuum booster assembly
Removal procedure 1. Remove the master cylinder. See Part 4B, "Master Cylinder" . 2. Remove the clamp securing the vacuum hose to the vacuum booster. 3....

General description and operation of the front brakes
Disc brake caliper The caliper has a double hole and is attached to the steering knuckle with two mounting bolts. The pressure in the hydraulic drive system,...

Front brake specifications
General technical characteristics Application Values Front brake discs Diameter 296 mm Thickness 29 mm Minimum allowable thickness 27.4 Lateral runout (in the...

Diagnosing Front Brake Faults
Inspection of brake pads 1. Raise and secure the vehicle. 2. Remove the front wheels. Follow section 2E, Tires and Wheels. 3. Inspect the brake pads and ensure...

Front brake pads — removal and installation
Removal procedure 1. Raise and support the vehicle. See Part 0B. General information. 2. To maintain wheel balance, you need to mark the position of the front...

Front caliper — removal and installation
Removal procedure 1. Raise and support the vehicle. See Part 0B. General information. 2. To maintain wheel balance, mark the position of the front wheel and...

Front Caliper Bracket
Removal procedure 1. Unscrew the caliper guide pin bolts, remove the caliper and pads. 2. Unscrew the caliper bracket mounting bolts. Installation procedure 1....

Front rotor, brake disc
Removal procedure 1. Remove the caliper bracket. See "Caliper Bracket" in this section. 2. Remove the disc lock screw. 3. Remove the brake disc. Installation...

Front mudguard, brake shield
Removal procedure 1. Remove the brake disc. See "Brake disc" in this section. 2. Remove the hub. See. 3. Remove the brake shield. Installation procedure 1....

General description and operation of the rear brakes
Disc brake caliper assembly The caliper has one cylinder and is attached to the steering knuckle with two bolts. The pressure in the hydraulic drive system,...

Rear brake specifications
General technical characteristics Application Values Front brake discs Diameter 303 mm Thickness 20 mm Minimum allowable thickness 18.4 Lateral runout (in the...

Rear Brake Fault Diagnosis
Inspection of brake pads and parking brake shoes 1. Raise and secure the vehicle. 2. Remove the rear wheels. Follow section 2E, Tires and Wheels. 3. Perform an...

Rear brake pads — removal and installation
Removal procedure 1. Raise and secure the vehicle. 2. Remove the rear wheels. Follow section 2E, Tires and Wheels. 3. Remove the brake caliper lower guide pin...

Rear Caliper — Removal and Installation
Removal procedure 1. Raise and secure the vehicle. 2. Mark the position of the rear wheels relative to the hubs and remove the wheels. Follow section 2E, Tires...

Rear Caliper Bracket
Removal procedure 1. Unscrew the caliper guide pin bolts, remove the caliper and pads. 2. Unscrew the caliper bracket mounting bolts. Installation procedure 1....

Rear rotor, brake disc
Removal procedure 1. Remove the caliper bracket. See "Caliper Bracket" in this section. 2. Remove the disc lock screw. 3. Remove the brake disc. Installation...

Rear hub and parking brake shoe/shield
Removal procedure 1. Remove the caliper bracket. 2. Remove the disc lock screw. 3. Remove the brake disc. 4. Disconnect the ABS sensor connector. 5. Unscrew...

General description and operation of the ABS system
General description of the system The ABS/TCS/ESP systems include several functional units and provide the volumetric pressure flow required to change the...

Technical characteristics of the ABS system
General technical characteristics Application Unit Description ABS mode - 4 channels, 4 sensors Hydraulic modulator Working voltage IN 10 - 16 Engine speed...

Schematic and assembly diagrams of the ABS system
ABS system circuit (I) ABS system circuit (II) Schematic diagram I - ABS Schematic diagram (II) - ABS with ESP (Electronic stability control system) View of...

Location of ABS system components
ABS system 1. Hydraulic block controller 2. Front wheel speed sensor 3. Rear wheel speed sensor

Diagnostics of ABS system malfunctions
Diagnostic Trouble Codes DTC Description C0035 Front Left Wheel Speed Sensor Circuit C0040 Front Right Wheel Speed Sensor Circuit C0045 Rear Left Wheel Speed...

ABS Diagnostic Trouble Codes
DTC C0035 - C0050 Description of the scheme The wheel speed sensor produces an AC signal whose amplitude and frequency vary with wheel speed. The electronic...

ABS Maintenance Precautions
Warning! Brake fluid can irritate eyes and skin. If it gets into your eyes or on your skin, take the following steps: In case of contact with eyes, rinse with...

ABS brake system controller
Removal procedure 1. Turn the ignition switch to the OFF position. 2. Remove the engine coolant reservoir and fuse box. See Section 1D2, Engine Cooling System...

Brake modulator assembly
Warning! Brake fluid can irritate eyes and skin. If it gets into your eyes or on your skin, take the following steps: In case of contact with eyes, rinse with...

Front wheel speed sensor
Removal procedure 1. Raise and secure the vehicle. 2. Remove the wheel and tire assembly. 3. Remove the brake disc. 4. Disconnect the wheel speed sensor...

Rear wheel speed sensor
Removal procedure 1. Raise and secure the vehicle. 2. Remove the wheel and tire assembly. 3. Remove the brake disc. 4. Disconnect the wheel speed sensor...

ESP Switch/DSC Switch
Removal procedure 1. Remove the silver moldings from the instrument panel. See section 9E, "Instruments/Driver Information System". 2. Remove the center...

Yaw rate sensor
Removal procedure 1. Remove the center panel. See section 9G, "Interior Trim". 2. Remove the yaw rate sensor. Installation procedure 1. Install the yaw rate...

General description and operation of the parking brake system
Parking brake This braking system uses a BRAKE indicator lamp located on the instrument panel. The indicator lamp lights up in the following cases: The parking...

Parking Brake Adjustment — Rear Disc Brakes
Adjustment procedure 1. Release the parking brake lever. 2. Raise and secure the vehicle. 3. Remove the rear wheels. Follow section 2E, Tires and Wheels. 4....

Parking brake indicator light switch
Removal procedure 1. Remove the parking brake/gear shift lever cover See section 9G, "Interior Trim". 2. Remove the parking brake lamp switch from the parking...

Parking brake lever
Removal procedure 1. Release the parking brake lever. 2. Remove the parking brake/shift lever console cover. See section 9G, "Interior Trim". 3. Measure the...

Parking brake cable
Removal procedure 1. Release the parking brake lever. 2. Remove the parking brake/shift lever console cover. See section 9G, "Interior Trim". 3. Measure the...

This section is available at russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share information:

Captiva 1 (2006-2018)